S355J0H

S355J0H

These grades of hollow section tubes offer various features including fire-resistant properties, high sectional properties, uniform mechanical properties, high compression capacity, suitable for low-temperature applications, and many more. Before dispatch of the product to the client, it is tested under various tests and is fully certified with standard forms. These hollow sections are available in many forms such as circular, rectangular, and square shapes. These hollow section pipes are suitable for the galvanizing process.

This Rectangular Hollow Section is obtainable through means of tailored solutions as per the drawings and designs given up by the clients. This grade of the hollow circular tube is mainly used in critical applications and is highly cost-effective. This EN 10219 S355J0H Rectangular Hollow Section is having commercial features through means of exceptional performances and the latest technology for meeting all budgets. The producers no doubt are ensuring that the item is produced by using the best quality of raw substances.

PRODUCT FEATURES

Designation for EN 10219 S355J0H sTEEL gRADE

  • The number of this European Standard (EN 10219 specification);
  • The capital letter S for structural steel;
  • The indication of the minimum specified yield strength for thickness ≤16mm is expressed in N/mm2;
  • The capital letters JR for the qualities with specified impact properties at room temperature;
  • The capital letter J and a number 0 or 2 for the qualities with specified impact properties at 0℃ and -20℃ respectively;
  • The capital letter H indicates hollow sections

Dimensions and Sizes of EN10219 S355J0H Pipe

NPS

O. D.

Nominal Wall Thickness

DN

Inch

mm

SCH5S

SCH10S

SCH10

SCH20

SCH30

SCH40

SCH60

SCH80

SCH100

SCH120

SCH140

SCH160

STD

XS

XXS

50

2″

60.3

1.65

2.77

3.91

5.54

8.74

3.91

5.54

11.07

65

2-1/2″

73

2.11

3.05

5.16

7.01

9.53

5.16

7.01

14.02

80

3″

88.9

2.11

3.05

5.49

7.62

11.13

5.49

7.52

15.24

90

3-1/2″

101.6

2.11

3.05

5.74

8.08

5.74

8.08

100

4″

114.3

2.11

3.05

6.02

8.58

11.13

13.49

6.02

8.56

17.12

125

5″

141.3

2.77

3.4

6.55

9.53

12.7

15.88

6.55

9.53

18.05

150

6″

168.3

2.77

3.4

7.11

10.97

14.27

18.26

7.11

10.97

21.95

200

8″

219.1

2.77

3.76

6.35

7.04

8.18

10.31

12.7

15.09

18.26

20.62

23.01

8.18

12.7

22.23

250

10″

273.1

3.4

4.19

6.35

7.8

9.27

12.7

15.09

18.26

21.44

25.4

28.58

9.27

12.7

25.4

300

12″

323.9

3.96

4.57

6.35

8.38

10.31

14.27

17.48

21.44

25.4

28.58

33.32

9.53

12.7

25.4

350

14″

355.5

3.96

4.78

6.35

7.92

9.53

11.13

15.09

19.05

23.83

27.79

31.75

35.71

9.53

12.7

400

16″

406.4

4.19

4.78

6.35

7.92

9.53

12.7

16.66

21.44

26.19

30.96

36.53

40.49

9.53

12.7

450

18″

457.2

4.19

4.78

6.35

7.92

11.13

14.27

19.05

23.83

39.36

34.93

39.67

45.24

500

20″

508

4.78

5.54

6.35

9.53

12.7

15.09

20.62

26.19

32.54

38.1

44.45

50.01

550

22″

558.8

4.78

5.54

6.35

9.53

12.7

22.23

28.58

34.93

41.28

47.63

53.98

600

24″

609.6

5.54

6.35

6.35

9.53

14.27

17.48

24.61

30.96

38.89

46.02

52.37

59.54

Weldability of EN 10219 S355J0H Pipe

This European standard only allows for the use of weldable steel. EN 1011-1 and EN 1011-2 specify the critical parameters for the welding of the products covered by this European standard.

While welding these materials, the primary worry is the development of cold cracking in the welded zone as the product’s thickness, strength level, and CEV grows. Cold cracking happens for a variety of reasons:

  • Enhanced diffusible hydrogen concentrations in the weld metal;
  • Brittle structure in the heat-affected zone;
  • High tensile stress concentrations in the welded joint

Chemical Composition % of Steel S355J0H (1.0547): EN 10219

Designation

Type of Deoxidation

Sub

Grop

C

%

max.

Nominal Thickness(mm)

Si

%

max.

Mn

%

max.

P

%

max.

S

%

max.

N

%

max.

According to EN10219-1 and lC 10

According to EN10219-1

≤40

>40≤65

S355J0H

1.0547

FN

QS

0.22

0.22

0.55

1.60

0.035

0.035

0.009-

1)      The deoxidation methods are designated as follows:

a)       FN = Rimming steel not permitted

b)      (e.g.min.0.020% total Al, or 0.015% soluble Al).

2)      QS-quality steel.

3)      It is permissible to exceed the specified values provided that for each increase of 0.001%N the P max content will be reduced by 0.005%, the N content of the ladle analysis, however, shall not be more than 0.012%

4)      The max. value for nitrogen does not apply if the chemical composition shows a minimum total Al content of0.020% with a minimum AL/N ratio of 2:1, or if sufficient other N-binding elements are present. The N-binding elements shall be recorded in lnspection Document.

Mechanical Properties for S355J0H Non-alloy Structural Steel

Designation

Minimum Yield Strength REh in

N/mm2

Tensile Strength Rm in

N/mm2

Minimum Percentage Elongation L0-5,65√S0

Impact Properties

Steel Name

Steel number

Nominal thickness in mm

Nominal thickness in mm

Longitudinal

Transverse

Test

Temperature

Minimum average absorbed energy(J)for standard test

pieces

≤16

>16≤40

>40≤65

<3

≥3≤65

Nominal thickness in mm

≤40

>40≤65

≤40

>40≤65

S355J0H

1.0547

355

345

335

510-680

490-630

22

21

20

19

0

27

Longitudinal values. Transverse values are 2 % lower.

For thicknesses < 3 mm, see 9.2.2.

The impact properties are verified only when Option 1.3 is specified.

For impact properties for reduced section test pieces see 6.6.2.

This value corresponds to 27J at -30 ℃.

Manufacturing Tolerances of EN 10219 S355J0H Pipe

Characteristic

Round Hollow Sections

Square and Rectangular Hollow Sections

Outside Dimension

± 1% with min ± 0.5mm and max ± 10mm

± 1% with min of ± 0.5mm

Thickness (T)

T≤5mm: ±10%

T≤5mm: ±10%

T>5mm: ± 0.5mm

T>5mm: ± 0.5mm

Out-of-Roundness

2%

Convexity

Max .8% with min 0.5mm

Squareness of side

90° ± 1°

External Corner Profile

T≤6mm: 1.6T to 2.4T

6<T≤10mm: 2.0T to 3.0T

T,10: 2.4T to 3.6T

Twist

2mm plus 0.5mm/m

Straightness

0.2% of total

0.15% of total

Mass

±6% on individual length

Inspection and Testing of EN 10219 S355J0H Hollow Sections of Non-alloy Steels

EN 10219 S355J0H is tensile tested according to EN 10002-1 and Charpy impact tested according to EN 10045-1.

Inspection Requirements

Inspection Frequency

Type of test

Non-specific

inspection

Specific inspection

Mandatory

tests

1

Cast analysis

One result per delivery

item

One per cast

2

Tensile test

One result per delivery

item

One per test unit ( b)

3

Impact test for

Qualities J2 and K2 only

Not applicable

One set per test unit (b)

4

Surface condition

and dimensions

5

NDT of the weld

Not applicable

All products, full length

Optional

tests

6

Product analysis

Not applicable

One per test unit a

7

Cast analysis

additional elements

Not applicable

See Option 1.2

8

Impact test for

qualities JR and J0

Not applicable

One set per test unit (b)

b – Longitudinal or transverse samples at the discretion of the manufacturer.

Marking of EN10219 S355J0H

Except as provided for in EN10219 10.2 for hollow sections which are bundled, each S355J0H section shall be marked by suitable and durable methods such as painting, stamping, adhesive labels, or attached tags with the following:

— the steel designation e.g., EN 10219-S355JOH;

— the manufacturer’s name or trademark;

— in the case of specific inspection: an identification number, e.g., order number, which permits the correlation of the product or delivery unit to the related document;

— the mark of the external inspection representative (where applicable).

 

When the items are provided bundled, the EN10219 10.1 marking must be on a label that is firmly affixed to the bundle.

Piling-pipe-supplied-by-Tianjin-United-Steel-Pipe
Piling Pipe
Hollow Section
show various kind of galvanized pipes
Galvanized Pipe
Steel Fabrication
Scroll to Top

Get A Quote Now

Fill in the form below and our team will be happy to assist you