S275J0H

shows-EN-10219-Steel-Pipe-S235JRH-S275J0H-S275J2H-S355J0H-S355J2H-S355K2H

S275J0H

S275J0H hollow sections are manufactured with EN 10210 and EN 10219 standards. Sectional dimensions are comparable for both hot finish and cold finish hollow sections, but the features are not, so double-check before ordering. S275J0H hollow section pipes and tubes can be welded or seamless and used for a variety of applications including anti-corrosive, mechanical, and structural.

The symbol S stands for structural steel, while the number 275 represents the minimum yield strength in thicknesses no larger than 16mm.

The symbol J and the letters 0 or 2 indicate that the quality has the required impact properties at 0°C and -20°C, respectively.

Hollow parts are denoted by the capital letter H.

This type of hollow section pipe is utilized in essential applications, and it has a variety of properties. These circular pipes are manufactured and exported based on client demand, and they are coated with anti-rust oil from the inside and outside of the pipes to assure their safety before being shipped to the end-users.

Why choose tuspipe?

pipe-icon

Since 1998, Tianjin United Steel Pipe Co., Ltd (TUSPIPE) has been committed to supplying high-quality line pipes.

With over 500,000 tons annual production capacity, the company serves various fields and industries, such as oil & gas exploitation and transmission, ship & auto-building, water & electricity, environmental protection, mechanical engineering, infrastructure construction and etc.

TUSPIPE places a premium on product quality and rigorous product quality control. In order to maintain good product quality,  the company has established a Test & Inspection Center since 2004. With a series of state-of-the-art tests and inspection equipment, the test & inspection center is able to perform the tensile tests, hydro tests, impact tests, DWTT, etc.

Play Video about Tianjin United Steel Pipe Co., Ltd office building

Designation for EN 10219 S275J0H Steel Grade

  • The number of this European Standard (EN 10219 specification);
  • The capital letter S for structural steel;
  • The indication of the minimum specified yield strength for thickness ≤16mm is expressed in N/mm2;
  • The capital letters JR for the qualities with specified impact properties at room temperature;
  • The capital letter J and a number 0 or 2 for the qualities with specified impact properties at 0℃ and -20℃ respectively;
  • The capital letter H indicates hollow sections

Dimensions and Sizes of EN10219 S275J0H Pipe

DNO. D.W. T.
InchmmSCH5SSCH10SSCH10SCH20SCH30SCH40SCH60SCH80SCH100SCH120SCH140SCH160STDXSXXS
502″60.31.652.77–––3.91–5.54–––8.743.915.5411.07
652 1/2″732.113.05–––5.16–7.01–––9.535.167.0114.02
803″88.92.113.05–––5.49–7.62–––11.135.497.5215.24
903 1/2″101.62.113.05–––5.74–8.08––––5.748.08–
1004″114.32.113.05–––6.02–8.58–11.13–13.496.028.5617.12
1255″141.32.773.4–––6.55–9.53–12.7–15.886.559.5318.05
1506″168.32.773.4–––7.11–10.97–14.27–18.267.1110.9721.95
2008″219.12.773.76–6.357.048.1810.3112.715.0918.2620.6223.018.1812.722.23
25010″273.13.44.19–6.357.89.2712.715.0918.2621.4425.428.589.2712.725.4
30012″323.93.964.57–6.358.3810.3114.2717.4821.4425.428.5833.329.5312.725.4
35014″355.53.964.786.357.929.5311.1315.0919.0523.8327.7931.7535.719.5312.7–
40016″406.44.194.786.357.929.5312.716.6621.4426.1930.9636.5340.499.5312.7–
45018″457.24.194.786.357.9211.1314.2719.0523.8339.3634.9339.6745.24–––
50020″5084.785.546.359.5312.715.0920.6226.1932.5438.144.4550.01–––
55022″558.84.785.546.359.5312.7–22.2328.5834.9341.2847.6353.98–––
60024″609.65.546.356.359.5314.2717.4824.6130.9638.8946.0252.3759.54–––

Weldability of EN 10219 S275J0H Pipe

This European standard specifies weldable steel. EN 1011-1 and EN 1011-2 provide the essential specifications for welding items covered by this European standard.

The greatest concern while welding these materials is the development of cold cracking in the welded zone as the thickness, strength level, and CEV of the product increase. Cold cracking occurs as a result of the following factors:

  • Enhanced diffusible hydrogen concentrations in the weld metal;
  • Brittle structure in the heat-affected zone;
  • High tensile stress concentrations in the welded joint

Chemical Composition for S275JOH Pipe Thicknesses ≤ 40 mm (Heat analysis in %)

Steel GradeMaterial NumberType of Deoxi- dation1)CSiMnPSN2)
S275J0H1.0149FF≤ 0,20–≤ 1,50≤ 0,035≤ 0,035≤ 0,009
1)      The deoxidation methods are designated as follows: FN-Rimming steel is not permitted.
2)      QS-quality steel.
3)      It is permissible to exceed the specified values provided that for each increase of 0.001% N the P max-cnotent will be reduced by 0.005%, the N content of the ladle analysis, however, shall not be more than 0.012%
4)      The max. value for nitrogen does not apply if the chemical composition shows a minimum total Al content of0.020% with a minimum ALN ratio of 2:1, or if sufficient other N-binding elements are present. The N-binding elements shall be recorded in the inspection Document.

Maximum Carbon Equivalent Value (CEV) of S275J0H Based on Cast Analysis

Steel GradeMaximum CEV for nominal
thicknesses ≤40 mm
Steel NameSteel Number%
S275JOH1.01490,40

Mechanical Properties of S275J0H at Room Temperature

Steel GradeMaterial NumberType of Deoxi- dation1)CSiMnPSN2)
S275J0H1.0149FF≤ 0,20–≤ 1,50≤ 0,035≤ 0,035≤ 0,009
1)      The deoxidation methods are designated as follows: FN-Rimming steel is not permitted.
2)      QS-quality steel.
3)      It is permissible to exceed the specified values provided that for each increase of 0.001% N the P max-cnotent will be reduced by 0.005%, the N content of the ladle analysis, however, shall not be more than 0.012%
4)      The max. value for nitrogen does not apply if the chemical composition shows a minimum total Al content of0.020% with a minimum ALN ratio of 2:1, or if sufficient other N-binding elements are present. The N-binding elements shall be recorded in the inspection Document.

Manufacturing Tolerances of EN 10219 S275J0H Pipe

CharacteristicRound Hollow SectionsSquare and Rectangular Hollow Sections
Outside Dimension± 1% with min ± 0.5mm and max ± 10mm± 1% with a min of ± 0.5mm
Thickness (T)T≤5mm: ±10%T≤5mm: ±10%
T>5mm: ± 0.5mmT>5mm: ± 0.5mm
Out-of-Roundness2%–
Convexity–Max .8% with min 0.5mm
Squareness of side–90° ± 1°
External Corner Profile–T≤6mm: 1.6T to 2.4T
–6<T≤10mm: 2.0T to 3.0T
–T,10: 2.4T to 3.6T
Twist–2mm plus 0.5mm/m
Straightness0.2% of total0.15% of total
Mass±6% on individual length

Inspection and Testing of EN 10219 S275J0H Hollow Sections of Non-alloy Steels

EN 10219 S275J2H is tensile tested according to EN 10002-1 and Charpy impact tested according to EN 10045-1.

Inspection RequirementsInspection Frequency
Type of testNon-specific
inspection
Specific inspection
Mandatory
tests
1Cast analysisOne result per delivery
item
One per cast
2Tensile testOne result per delivery
item
One per test unit ( b)
3Impact test for
Qualities J2 and K2 only
Not applicableOne set per test unit (b)
4Surface condition
and dimensions
––
5NDT of the weldNot applicableAll products, full length
Optional
tests
6Product analysisNot applicableOne per test unit a
7Cast analysis
additional elements
Not applicableSee Option 1.2
8Impact test for
qualities JR and J0
Not applicableOne set per test unit (b)
b – Longitudinal or transverse samples at the discretion of the manufacturer.
Piling-pipe-supplied-by-Tianjin-United-Steel-Pipe
Piling Pipe
Square-Hollow-Section-SHS
Hollow Section
show various kind of galvanized pipes
Galvanized Pipe
Pipe-Fabrication-Spooling
Steel Fabrication
Scroll to Top

Get A Quote Now

Fill in the form below and our team will be happy to assist you