S355J0H

shows-EN-10219-Steel-Pipe-S235JRH-S275J0H-S275J2H-S355J0H-S355J2H-S355K2H

S355J0H

S355JOH hollow section tubes offer various features including fire-resistant properties, high sectional properties, uniform mechanical properties, high compression capacity, suitable for low-temperature applications, and many more. Before dispatch of the product to the client, it is tested under various tests and is fully certified with standard forms. These hollow sections are available in many forms such as circular, rectangular, and square shapes. These hollow section pipes are suitable for the galvanizing process.

This Rectangular Hollow Section is obtainable through means of tailored solutions as per the drawings and designs gave up by the clients. This grade of hollow circular tube is mainly used in critical applications and is highly cost-effective. This EN 10219 S355J0H Rectangular Hollow Section is having commercial features through means of exceptional performances and the latest technology for meeting all budgets. The producers no doubt are ensuring that the item is produced by using the best quality raw substances.

Why choose tuspipe?

pipe-icon

Since 1998, Tianjin United Steel Pipe Co., Ltd (TUSPIPE) has been committed to supplying high-quality line pipes.

With over 500,000 tons annual production capacity, the company serves various fields and industries, such as oil & gas exploitation and transmission, ship & auto-building, water & electricity, environmental protection, mechanical engineering, infrastructure construction and etc.

TUSPIPE places a premium on product quality and rigorous product quality control. In order to maintain good product quality,  the company has established a Test & Inspection Center since 2004. With a series of state-of-the-art tests and inspection equipment, the test & inspection center is able to perform the tensile tests, hydro tests, impact tests, DWTT, etc.

Play Video about Tianjin United Steel Pipe Co., Ltd office building

Designation for EN 10219 S355J0H Steel Grade

  • The number of this European Standard (EN 10219 specification);
  • The capital letter S for structural steel;
  • The indication of the minimum specified yield strength for thickness ≤16mm is expressed in N/mm2;
  • The capital letters JR for the qualities with specified impact properties at room temperature;
  • The capital letter J and a number 0 or 2 for the qualities with specified impact properties at 0℃ and -20℃ respectively;
  • The capital letter H indicates hollow sections

Dimensions and Sizes of EN10219 S355J0H Pipe

DNO. D.W. T.
InchmmSCH5SSCH10SSCH10SCH20SCH30SCH40SCH60SCH80SCH100SCH120SCH140SCH160STDXSXXS
502″60.31.652.77–––3.91–5.54–––8.743.915.5411.07
652 1/2″732.113.05–––5.16–7.01–––9.535.167.0114.02
803″88.92.113.05–––5.49–7.62–––11.135.497.5215.24
903 1/2″101.62.113.05–––5.74–8.08––––5.748.08–
1004″114.32.113.05–––6.02–8.58–11.13–13.496.028.5617.12
1255″141.32.773.4–––6.55–9.53–12.7–15.886.559.5318.05
1506″168.32.773.4–––7.11–10.97–14.27–18.267.1110.9721.95
2008″219.12.773.76–6.357.048.1810.3112.715.0918.2620.6223.018.1812.722.23
25010″273.13.44.19–6.357.89.2712.715.0918.2621.4425.428.589.2712.725.4
30012″323.93.964.57–6.358.3810.3114.2717.4821.4425.428.5833.329.5312.725.4
35014″355.53.964.786.357.929.5311.1315.0919.0523.8327.7931.7535.719.5312.7–
40016″406.44.194.786.357.929.5312.716.6621.4426.1930.9636.5340.499.5312.7–
45018″457.24.194.786.357.9211.1314.2719.0523.8339.3634.9339.6745.24–––
50020″5084.785.546.359.5312.715.0920.6226.1932.5438.144.4550.01–––
55022″558.84.785.546.359.5312.7–22.2328.5834.9341.2847.6353.98–––
60024″609.65.546.356.359.5314.2717.4824.6130.9638.8946.0252.3759.54–––

Weldability of EN 10219 S355J0H Pipe

This European standard only allows for the use of weldable steel. EN 1011-1 and EN 1011-2 specify the critical parameters for the welding of the products covered by this European standard.

While welding these materials, the primary worry is the development of cold cracking in the welded zone as the product’s thickness, strength level, and CEV grows. Cold cracking happens for a variety of reasons:

  • Enhanced diffusible hydrogen concentrations in the weld metal;
  • Brittle structure in the heat-affected zone;
  • High tensile stress concentrations in the welded joint

Chemical Composition % of Steel S355J0H (1.0547): EN 10219

DesignationType of deoxidationSub
Grop
C
%
max.
Nominal thickness(mm)
Si
%
max.
Mn
%
max.
P
%
max.
S
%
max.
N
%
max.
According to EN10219-1 and lC 10According to EN10219-1≤40>40≤65
S355J0H1.0547FNQS0.220.220.551.60.0350.0350.009-
1)      The deoxidation methods are designated as follows:
 a)       FN = Rimming steel not permitted
 b)      (e.g.min.0.020% total Al, or 0.015% soluble Al).
2)      QS-quality steel.
3)      It is permissible to exceed the specified values provided that for each increase of 0.001%N the P max content will be reduced by 0.005%, the N content of the ladle analysis, however, shall not be more than 0.012%
4)      The max. value for nitrogen does not apply if the chemical composition shows a minimum total Al content of0.020% with a minimum AL/N ratio of 2:1, or if sufficient other N-binding elements are present. The N-binding elements shall be recorded in lnspection Document.

Mechanical Properties for S355J0H Non-alloy Structural Steel

DesignationMinimum Yield Strength REh in
N/mm2
Tensile Strength Rm in
N/mm2
Minimum percentage elongation L0-5,65√S0Impact properties
Steel NameSteel numberNominal thickness in mmNominal thickness in mmLongitudinalTransverseTest
Temperature
Minimum average absorbed energy(J)for standard test
pieces
≤16>16≤40>40≤65<3≥3≤65Nominal thickness in mm
≤40>40≤65≤40>40≤65
S355J0H1.0547355345335510-680490-63022212019027

Longitudinal values. Transverse values are 2 % lower.

For thicknesses < 3 mm, see 9.2.2.

The impact properties are verified only when Option 1.3 is specified.

For impact properties for reduced section test pieces see 6.6.2.

This value corresponds to 27J at -30 ℃.

Manufacturing Tolerances of EN 10219 S355J0H Pipe

CharacteristicRound Hollow SectionsSquare and Rectangular Hollow Sections
Outside Dimension± 1% with min ± 0.5mm and max ± 10mm± 1% with min of ± 0.5mm
Thickness (T)T≤5mm: ±10%T≤5mm: ±10%
T>5mm: ± 0.5mmT>5mm: ± 0.5mm
Out-of-Roundness2%–
Convexity–Max .8% with min 0.5mm
Squareness of side–90° ± 1°
External Corner Profile–T≤6mm: 1.6T to 2.4T
–6<T≤10mm: 2.0T to 3.0T
–T,10: 2.4T to 3.6T
Twist–2mm plus 0.5mm/m
Straightness0.2% of total0.15% of total
Mass±6% on individual length

Inspection and Testing of EN 10219 S355J0H Hollow Sections of Non-alloy Steels

EN 10219 S355J0H is tensile tested according to EN 10002-1 and Charpy impact tested according to EN 10045-1.

Inspection RequirementsInspection Frequency
Type of testNon-specific
inspection
Specific inspection
Mandatory
tests
1Cast analysisOne result per delivery
item
One per cast
2Tensile testOne result per delivery
item
One per test unit ( b)
3Impact test for
Qualities J2 and K2 only
Not applicableOne set per test unit (b)
4Surface condition
and dimensions
––
5NDT of the weldNot applicableAll products, full length
Optional
tests
6Product analysisNot applicableOne per test unit a
7Cast analysis
additional elements
Not applicableSee Option 1.2
8Impact test for
qualities JR and J0
Not applicableOne set per test unit (b)
b – Longitudinal or transverse samples at the discretion of the manufacturer.

Marking of EN10219 S355J0H

Except as provided for in EN10219 10.2 for hollow sections which are bundled, each S355J0H section shall be marked by suitable and durable methods such as painting, stamping, adhesive labels, or attached tags with the following:

— the steel designation e.g., EN 10219-S355JOH;

— the manufacturer’s name or trademark;

— in the case of specific inspection: an identification number, e.g., order number, which permits the correlation of the product or delivery unit to the related document;

— the mark of the external inspection representative (where applicable).

 

When the items are provided bundled, the EN10219 10.1 marking must be on a label that is firmly affixed to the bundle.

Piling-pipe-supplied-by-Tianjin-United-Steel-Pipe
Piling Pipe
Square-Hollow-Section-SHS
Hollow Section
show various kind of galvanized pipes
Galvanized Pipe
Pipe-Fabrication-Spooling
Steel Fabrication
Scroll to Top

Get A Quote Now

Fill in the form below and our team will be happy to assist you